This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
wiki:simple_outdoor_enclosure_mounting [2021/11/06 16:45] vizycam |
wiki:simple_outdoor_enclosure_mounting [2021/11/06 17:17] (current) vizycam |
||
---|---|---|---|
Line 6: | Line 6: | ||
===== Pole-in-ground mounting ==== | ===== Pole-in-ground mounting ==== | ||
- | In particular, you can take a 1.5" PVC pipe and cut it to the desired length and drive it into the ground for a simple camera mount that will stay where you want it. Angle-cut the PVC pipe (see below), which makes it easy to drive into the ground. Combine with one of the camera mounts below. | + | In particular, you can take a 1.5" PVC pipe and cut it to the desired length and drive it into the ground for a simple camera mount that will stay put. Angle-cut the PVC pipe (see below), which makes it easy to drive into the ground. Combine with one of the camera mounts below. |
{{wiki:image_504.jpg?600}} | {{wiki:image_504.jpg?600}} | ||
- | ===== Hang/cantelever mounting ===== | + | ===== Cantilever mounting ===== |
Again by using 1.5" PVC piping, the same mounting ideas can be applied to other setups, such as mounting from the underside of a roof eave. That is, you can use a [[https://www.amazon.com/CIRCOPACK-Screw-Schedule-Furniture-pieces/dp/B07WGWB6TY|screw-tab cap]] in combination with PVC elbows to create a mount that fits your needs. Combine with one of the camera mounts below. | Again by using 1.5" PVC piping, the same mounting ideas can be applied to other setups, such as mounting from the underside of a roof eave. That is, you can use a [[https://www.amazon.com/CIRCOPACK-Screw-Schedule-Furniture-pieces/dp/B07WGWB6TY|screw-tab cap]] in combination with PVC elbows to create a mount that fits your needs. Combine with one of the camera mounts below. | ||
Line 41: | Line 41: | ||
You can then place the cap on top of the PVC pipe. No PVC adhesive is necessary. | You can then place the cap on top of the PVC pipe. No PVC adhesive is necessary. | ||
+ | {{wiki:image_518b.jpg?600}} | ||
===== Adjustable angle camera mount ===== | ===== Adjustable angle camera mount ===== | ||
Line 46: | Line 47: | ||
Materials needed (in addition to 1.5" PVC pipe): | Materials needed (in addition to 1.5" PVC pipe): | ||
+ | - 1.5" PVC cap | ||
- Ball head camera mount ([[https://www.amazon.com/gp/product/B08R7TSNP2|Amazon B08R7TSNP2]], or [[https://www.amazon.com/dp/B096K1X5NG|Amazon B096K1X5NG]], etc.) | - Ball head camera mount ([[https://www.amazon.com/gp/product/B08R7TSNP2|Amazon B08R7TSNP2]], or [[https://www.amazon.com/dp/B096K1X5NG|Amazon B096K1X5NG]], etc.) | ||
- 1/4"-20 x 0.5" stainless bolt | - 1/4"-20 x 0.5" stainless bolt | ||
Line 64: | Line 66: | ||
You can then place the cap on top of the PVC pipe. No PVC adhesive is necessary. The ball mount gives you 3 degrees of easy adjustment. | You can then place the cap on top of the PVC pipe. No PVC adhesive is necessary. The ball mount gives you 3 degrees of easy adjustment. | ||
+ | {{wiki:image_519b.jpg?600}} | ||