This shows you the differences between two versions of the page.
Next revision | Previous revision Next revision Both sides next revision | ||
wiki:simple_outdoor_enclosure_mounting [2021/11/06 16:23] vizycam created |
wiki:simple_outdoor_enclosure_mounting [2021/11/06 16:39] vizycam |
||
---|---|---|---|
Line 7: | Line 7: | ||
- | The same mounting ideas can be applied to other setups, such as mounting from the underside of an eave. That is, you can use a [[https://www.amazon.com/CIRCOPACK-Screw-Schedule-Furniture-pieces/dp/B07WGWB6TY|screw-tab cap]] in combination with PVC elbows to create a mount that fits your application. | + | The same mounting ideas can be applied to other setups, such as mounting from the underside of a roof eave. That is, you can use a [[https://www.amazon.com/CIRCOPACK-Screw-Schedule-Furniture-pieces/dp/B07WGWB6TY|screw-tab cap]] in combination with PVC elbows to create a mount that fits your needs. |
Line 27: | Line 27: | ||
{{wiki:image_510.jpg?600}} | {{wiki:image_510.jpg?600}} | ||
- | Place another nut and washer on the top and thread the bolt into the nut of the outdoor enclosure and tighten with a wrench. | + | Place another nut and washer on the top and thread the bolt into the nut of the outdoor enclosure. |
{{wiki:image_511.jpg?600}} | {{wiki:image_511.jpg?600}} | ||
- | You can then place the cap on top of the PVC pipe. No adhesive is necessary. | + | Tighten with a wrench. |
+ | |||
+ | {{wiki:image_512.jpg?600}} | ||
+ | |||
+ | You can then place the cap on top of the PVC pipe. No PVC adhesive is necessary. | ||
Line 38: | Line 42: | ||
Materials needed (in addition to 1.5" PVC pipe): | Materials needed (in addition to 1.5" PVC pipe): | ||
- | - Ball head camera mount ([[https://www.amazon.com/gp/product/B08R7TSNP2|Amazon B08R7TSNP2]], or [[https://www.amazon.com/dp/B096K1X5NG|Amazon B096K1X5NG, etc.) | + | - Ball head camera mount ([[https://www.amazon.com/gp/product/B08R7TSNP2|Amazon B08R7TSNP2]], or [[https://www.amazon.com/dp/B096K1X5NG|Amazon B096K1X5NG]], etc.) |
- 1/4"-20 x 0.5" stainless bolt | - 1/4"-20 x 0.5" stainless bolt | ||
- 1/4" washer | - 1/4" washer | ||
- | The mount starts with a 1.5" PVC cap with a 1/4" hole drilled into the center. | + | The mount starts with a 1.5" PVC cap with a 1/4" hole drilled into the center. Take a 1/4"-20 x 0.5" bolt with washer and thread into the underside of the cap. |
+ | {{wiki:image_514.jpg?600}} | ||
- | Take a 1/4"-20 x 0.5" bolt with washer and thread into the underside of the cap. | + | Tighten onto the ball mount with a screwdriver. |
+ | {{wiki:image_515.jpg?600}} | ||
- | Tighten onto the the ball mount with a screwdriver. | + | Thread the ball mount onto the outdoor enclosure and tighten. |
+ | {{wiki:image_516.jpg?600}} | ||
- | Thread the ball mount onto the outdoor enclosure and tighten. You can then place the cap on top of the PVC pipe. No adhesive is necessary. The ball mount gives you 3 degrees of easy adjustment freedom. | + | You can then place the cap on top of the PVC pipe. No PVC adhesive is necessary. The ball mount gives you 3 degrees of easy adjustment. |